I have mild ptosis, about 1cm below the crease. What size/type implant is best without having to get a lift? My measurements are: sternal notch to nipple- 21cm; ribcage- 28in.; ribspan- 25.5cm; bwd- 12cm. I would like to be a D cup. I'm thinking Mentor smooth round hp with 400-425cc under the muscle. What are your opinions?
Hello, I went to my first consultation for a breast augmentation. I am 5'1 105 pounds and a small A cup. I have had one child so my breasts have that deflated look with no volume on top. I want silicone implants and want to be a C cup. My surgeon recommended Mentor HP implants due to my chest size and such. I stated that I wanted my breasts to still look natural and fit my frame so he recommended 375cc or 400cc implant size. Will that size be too large and make me more of a D cup?
Hello All. English is not my mother language however I shall try to to describe the issue. I have attended 1 consultation. Doctor advised me to go with Mentor 330cc 322 cpg or 345cc 323 cpg. I am 5 feet 0 inch, weight is approx. 105 lbs. I have 27.75 inch band size and 33.00 inch in bust. Doctor said my BWD is 5 inch 1/8 (13 cm ). However, could you advise me if with 330 cc i will get the desired look or should I insist to go with 390 cc 323 cpg? For me the most important is health.
I'm 5'1 120 lbs diam 12.5 and wanting a full C. My surgeon suggested me to go for mentor 425 cc Hp round texture and still acheive a natural slope breast. Is that implant might be too big? I was thinking to go for 375cc. Would this size also give me at least a C cup? Is it possible for 375cc and profile is moderate plus? As I know the hp looks is more fade.
My stats are 5'3 110lbs 12bwd starting with virtually no tissue and the bones on my right side are more prominent with a hollow under my left. Ive chosen saline implants. My PS works with mentor and his suggestion being 250-375cc HP or UHP implants over filled which Im realizing is quite small for 12bwd based on the mentor chart. Im starting to doubt his recommendation and am curious to see what others would choose for me and why.
Tried both in my sizing appt, 250 seemed too small and 315 was almost too big. I liked the look of the 250 sizers at home but am reading that it will look smalller due to compression. 3D views look very similar but know that all three tests arent accurate. I am athletic and but also like the larger look. Help! Decision needed soon.
mMy pre op chest width is 13. I just had my first silicone (425cc) Mentor round high profile implant 4 days ago. My original size was 34A. I wanted to look bigger and fuller (full C small D). I am 5ft 130 lbs (big bone, wide hip, size 4 pants, small size dress/shirt). After surgery, I felt that I am only full B cup. 2 days post op I saw my surgeon and he said that 425 cc was the max he could put in because of my small frame. if without being swollen now I feel I am still small, I'm thinking that in 3 months after the dropping, I'll still feel smaller?
I am 22, 5'3 and 117 pounds. Sometimes down to 110. So anyways i have a bwd of 13.5 going with silicone gel mentor brand. I had 2 kids. When engorged with milk i was a 34d. My doctor said 425 mod+ was the biggest he could do then i asked about 475/500 in hp since they are same diameter he said hed do whatever i pick the vectra3d looked great he said itd give more roundness on top than it showed. Some fake is okay im small going big so itll be somewhat fake but i dont want circle boobs nor saggy.
Me: 5'3 135 lbs chest diameter= 12 in. The mentor 325cc diameter is 12.3 and projection 3.8c / moderate plus 350 diameter is 12/ projection 4.6- high profile I'm wondering what would fit and look the best on a short stature. I know there is a small different in volume and they look a little smaller going under the muscle. I'm hesitant about the HP because I am short. I just want overal attractive boobs when I'm done and nothing that sticks out too far. Thank you!